register at Windows8Downloads.com Windows 8 Downloads RSS add Windows 8 Downloads to favorites

Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03 Windows 8 driver download - Windows 8 Downloads

Windows 8 driver

Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03



Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03 - Details

Download Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03

Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03 driver for Windows 8 - Full description

NEW FEATURES

1) Correction of the noise that might be observed when “Simultaneous REC” is set and “REC Button” or “Handle REC Button” is assigned to record to memory cards A or B separately in DV recording mode.

2) Correction of information display through HDMI output even if “Display Output” is set to “LCD Panel” when “Spot Meter/Focus” or “Spot Meter” is set.

System software update

1. Download the update file

Please save the downloaded file onto the Desktop of your computer (recommended).

2. Start up Firmware Updater

Please close all other application software before updating the system software .

Double-click downloaded file to start up Firmware Updater

3. Connect the camera to the computer

Camera power on by AC adapter.

Note: Never power off until finish the upgrading.

Connect the camera to the computer with the USB cable.

Select Update on the camera screen.

After confirm “Mass Storage Connected” is displayed on the camera screen, click the [Next] button on Firmware Updater.

4. Check if the update is required

Click the [Next] button to check version.

After confirming the current version on the screen, click the [Next] button.

5. Reset the camera

Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.

Touch [OK] on LCD to reset camera body, after then Click the [NEXT] button.

Note: Don’t push [RESET] button on the camera, please proceed to the next step.

6. Start the update

After resetting, reconnection of the camera is verified, and the “Run the update” screen appears.

Click the [Run] button to start the update. The progress bar appears while updating (approximately 5 minutes).

Note: Never turn off the camera nor disconnect the USB cable while upgrading.

7. Complete the update

When the update is completed, the “Finish the update” screen appears.

Click the [Finish] button and disconnect the USB cable.

Note: After finished the update, turn off the camera, remove the AC adaptor, and then turn on the camera again.

8. Check the system software version

About Digital Camera Firmware:

Updating to a newer firmware version than the one already installed on your camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.

On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.

It is recommended that changing the camera’s firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.

This process isn’t intended to be destructive, but still, it’s best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don’t use the camera’s buttons while the installation is in progress.

When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device’s update section.

However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product’s installation guide.

That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don’t miss the update that will boost your camera’s performance.



Windows 8 Sony HXR-NX3/1 NXCAM Camcorder Firmware 1.03 related drivers

Improvements over version 2.00: - Provides the Half-Press shutter function - Improves the NFC One-touch connection (the connection time is reduced) Benefits provided by previous updates and included in version 3.00: - Adds S-mode (Shutter Priority mode) and manual ISO sensitivity to the wide-ranging setting ...
This utility updates the camera firmware to version 1.04 and provides the following benefits: Improvements over firmware version 1.02:- Adds support for the camera to display focal length information about an attached Zoom Lens DT 55-200mm F4-5.6. Additional improvements over original firmware:- Addresses the symptom where, in very rare cases, RAW ...
Fixes:- "Loop recording" mode has been added to shooting mode setting  - The following features have been added to camera setting  - Image quality setting has been added  - Movie format setting has been added - Date and time/area/daylight saving time (summer time) setting has been changed - Time zone of ...
Fixes: - Phase-detection AF is supported - The lens name will be correctly recorded in the EXIF - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the ...
This utility updates the camera firmware to version 1.04 and provides the following benefits: Improvements over firmware version 1.02:- Adds support for the camera to display focal length information about an attached Zoom Lens DT 55-200mm F4-5.6. Additional improvements over original firmware:- Addresses the symptom where, in very rare cases, RAW ...
Fixes:- The lens name will be correctly recorded in the EXIF - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the update process. - Download the firmware ...
This package provides the necessary installation files of Sony ILCE-7SM2 Camera Firmware 2.1.Improvements:- Allows the camera to record XAVCS format video with an SDHC card in addition to SDXC card. Notes:- When an SDHC memory card is used to record movies in XAVC S format over extended periods of time, the ...
Fixes:  - "Loop recording" mode has been added to shooting mode setting - The following features have been added to camera setting - Image quality setting has been added  - Movie format setting has been added - Date and time/area/daylight saving time (summer time) setting has been changed - Time zone ...
Fixes:  - "Loop recording" mode has been added to shooting mode setting - The following features have been added to camera setting - Image quality setting has been added  - Movie format setting has been added - Date and time/area/daylight saving time (summer time) setting has been changed - Time zone ...
Improvements: - Adds support for Radio Controlled Lighting System - Improves stability in picture shooting mode (optimizing temperature control, effect is different according to temperature) - Adds support to output video via HDMI (still mode) when using the Remote Camera Control software - Improves overall stability and operability of the ...

My Account

Advertise Link To Us Privacy Policy Contact Us