ePrivacy and GPDR Cookie Consent by Cookie Consent
register at Windows8Downloads.com Windows 8 Downloads RSS add Windows 8 Downloads to favorites Windows 8 Downloads bookmark

NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21 Windows 8 driver download - Windows 8 Downloads

Windows 8 driver

NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21



NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21 - Details

Download NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21

NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21 driver for Windows 8 - Full description

Changes:

- The focus distance displayed in the lens info panel immediately after the camera was turned on would sometimes not change if the zoom ring was rotated while the camera was off. In rare cases, this would cause autofocus to stop.
- When an option other than Non-linear was selected for Custom Setting f9 (Focus ring rotation range), a beep would sound to signal that a stored focus position had been recalled despite the focus ring having been rotated to end memory recall before completion of the recall operation initiated by pressing the camera control to which Recall focus position was assigned.

Viewing the Lens Firmware Version:

- Attach the lens to the camera and turn the camera on.
- Press the camera MENU button and select SETUP MENU > Firmware version to display the camera and lens firmware versions.
- Check the firmware version.
- Turn the camera off.

Updating the Lens Firmware:

- Create a folder on the computer hard disk, name it as desired, and dwnload the firmware there.
- Run the package to extract the lens firmware file (.bin).
- Using a card slot or card reader, copy the .bin file to a memory card that has been formatted in the camera.
- Note: Be sure to copy the firmware to the root (top-most) directory of the memory card. The camera will not recognize the new firmware if it is placed in a folder under the root directory.
- Insert the memory card into the camera and turn the camera on.
- Select SETUP MENU > Firmware version and follow the on-screen instructions to perform the firmware update.
- When a message is displayed stating that the update is complete, turn the camera off and remove the memory card.
- Turn the camera on and confirm that the firmware has been updated to the new version.

About Lens Updates:

Upgrading or downgrading your lens to a different firmware version might enhance the unit's overall performance and stability, and could also improve some of the lenses' features (a good example would be faster autofocus speed).

In order to apply a firmware properly, other than the one already installed, you should check that the lenses are connected to the camera body, copy the compatible update on a memory card, and insert it into the camera.

From the device's menu, browse to the Firmware Upgrade section, and enable the new firmware. Since each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, you must make sure that you read the product's installation guide.

Therefore, if you consider installing this present release, click on the download button to get the firmware, and apply it. Moreover, don't forget to check our website constantly so that you don't miss any of the future versions.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.



Windows 8 NIKKOR Z 70-200mm f/2.8 VR S Lens Firmware 1.21 related drivers

Fixed issues: - Fixed an issue that sometimes resulted in the image in the monitor being out of focus when the camera was turned on. Viewing the Camera Firmware Version: - Turn the camera on. - Press the camera MENU button to display the menus. - Press the ...
Changes: - The camera would sometimes freeze when turned on under water. - The location data display for active mode showed seconds in base 10. - Improved the accuracy of location data in certain locations (specifically, those locations where location data are augmented by data from “Michibiki” QZSS satellites). Viewing ...
This package provides the necessary upgrade files of Nikon COOLPIX S6800 Camera Firmware version 1.1.  Fixes: - Occurrence of an issue that in some rare cases prevented proper recovery of the camera, even when it was turned off and then on again, when a lens error occurred has been reduced.About ...
Changes: - In certain locations, location data could sometimes be inaccurate, unavailable, or unreliable. - The display would sometimes fail to follow changes to camera orientation (portrait to landscape or vice versa). - Interval timer photography would end after 1800 shots. - The camera would sometimes stop responding to controls other ...
Changes: - Fixed an issue that in rare cases would prevent the camera turning on even when a battery with sufficient charge was inserted. - Updated some help text. Viewing the Camera Firmware Version: - Turn the camera on. - Press the camera MENU button to display the ...
Changes: - Setup Menu: The language that is set may not be displayed correctly. Confirming the firmware version - Turn on the camera. - Press the camera’s MENU button and select Firmware version from the setup menu. - The camera's A and B firmware versions will be displayed. - ...
Changes from “C” Firmware Version 1.00 to 1.10 - The camera can now record movies up to 29 minutes and 59 seconds long. Movies are recorded across up to 8 files, each up to 4 GB size, which can be joined together using the ViewNX-Movie Editor option in ViewNX-i version ...
Changes: - Fixed an issue that sometimes caused the camera to stop responding when attached to a WR‑R10 wireless remote controller running firmware version 3.00. Updating the Camera Firmware: - Save and run the downloadable file to create a “D810Update” folder. - Using a card slot or card reader, copy ...
Changes: - The D5 and D500 ISO sensitivity displays are now supported. If you are using two WR-1 units, one as a receiver and the other as a transmitter, update both to firmware version 1.01. - When used as a transmitter to change ISO sensitivity for a receiving camera, the ...
Changes: - Fixed an issue that occurred with WR-R10 wireless remote controller firmware version 3.00. In rare cases, the camera would fail to display the number of exposures remaining or would take about a minute to power down when the WR-R10 was connected. Viewing the Camera Firmware Version - ...

My Account

Advertise Link To Us Privacy Policy Contact Us